require `uasyncio` but are compatible with it, and are designed for standard
firmware builds.
-The receiver is cross platform and has been tested on Pyboard, ESP8266 and
-ESP32. The transmitter driver is compatible with Pyboard (1.x and D series) and
-also (subject to limitations) with ESP32. For the transmitter a Pyboard is
-recommended.
+The receiver is cross platform and has been tested on Pyboard, ESP8266, ESP32
+and Raspberry Pi Pico.
-The transmitter is documented [here](./TRANSMITTER.md) and the receiver is
-[here](./RECEIVER.md).
+In a typical use case the receiver is employed at the REPL to sniff the address
+and data values associated with buttons on a remote control. The transmitter is
+then used in an application to send those codes, emulating the remote control.
+
+Other use cases involve running the receiver in an application. This enables an
+IR remote to control a device such as a robot.
+
+#### [Receiver docs](./RECEIVER.md)
+
+The transmitter driver is compatible with Pyboard (1.x and D series) and ESP32.
+ESP8266 is unsupported; it seems incapable of generating the required signals.
+
+#### [Transmitter docs](./TRANSMITTER.md)
# 1. IR communication
takes the form of OOK (on-off keying). There are multiple protocols and at
least three options for carrier frequency: 36, 38 and 40KHz.
+In the case of the transmitter the carrier frequency is a runtime parameter:
+any value may be specified. The receiver uses a hardware demodulator which
+should be purchased for the correct frequency. The receiver device driver sees
+the demodulated signal and is hence carrier frequency agnostic.
+
+Remotes transmit an address and a data byte, plus in some cases an extra value.
+The address denotes the physical device being controlled. The data defines the
+button on the remote. Provision usually exists for differentiating between a
+button repeatedly pressed and one which is held down; the mechanism is protocol
+dependent.
+
+# 2. Supported protocols
+
The drivers support NEC and Sony protocols plus two Philips protocols, namely
-RC-5 and RC-6 mode 0. In the case of the transmitter the carrier frequency is a
-runtime parameter: any value may be specified. The receiver uses a hardware
-demodulator which should be purchased for the correct frequency. The receiver
-device driver sees the demodulated signal and is hence carrier frequency
-agnostic.
+RC-5 and RC-6 mode 0. There is also support for the OrtekMCE protocol used on
+VRC-1100 remotes. These originally supported Microsoft Media Center but can be
+used to control Kodi and (with a suitable receiver) to emulate a PC keyboard.
Examining waveforms from various remote controls it is evident that numerous
protocols exist. Some are doubtless proprietary and undocumented. The supported
A remote using the NEC protocol is [this one](https://www.adafruit.com/products/389).
-Remotes transmit an address and a data byte, plus in some cases an extra value.
-The address denotes the physical device being controlled. The data defines the
-button on the remote. Provision usually exists for differentiating between a
-button repeatedly pressed and one which is held down; the mechanism is protocol
-dependent.
-
-# 2. Hardware Requirements
+# 3. Hardware Requirements
These are discussed in detail in the relevant docs; the following provides an
overview.
The transmitter requires a Pyboard 1.x (not Lite), a Pyboard D or an ESP32.
Output is via an IR LED which will need a transistor to provide sufficient
-current. The ESP32 has significant limitations as a transmitter discussed
-[here](./TRANSMITTER.md#52-esp32).
+current. The ESP32 requires an extra transistor to work as a transmitter.
+
+## 3.1 Carrier frequencies
+
+These are as follows. The Samsung and Panasonic remotes appear to use
+proprietary protocols and are not supported by these drivers.
+
+| Protocol | F KHz | How found | Support |
+|:---------:|:-----:|:-------------:|:-------:|
+| NEC | 38 | Measured | Y |
+| RC-5 RC-6 | 36 | Spec/measured | Y |
+| Sony | 40 | Spec/measured | Y |
+| MCE | 38 | Measured | Y |
+| Samsung | 38 | Measured | N |
+| Panasonic | 36.3 | Measured | N |
+
+# 4. References
+
+Sources of information about IR protocols. The `sbprojects.net` site is an
+excellent resource.
+[General information about IR](https://www.sbprojects.net/knowledge/ir/)
+
+The NEC protocol:
+[altium](http://techdocs.altium.com/display/FPGA/NEC+Infrared+Transmission+Protocol)
+[circuitvalley](http://www.circuitvalley.com/2013/09/nec-protocol-ir-infrared-remote-control.html)
+[sbprojects.net](https://www.sbprojects.net/knowledge/ir/nec.php)
+
+Philips protocols:
+[RC5 Wikipedia](https://en.wikipedia.org/wiki/RC-5)
+[RC5 sbprojects.net](https://www.sbprojects.net/knowledge/ir/rc5.php)
+[RC6 sbprojects.net](https://www.sbprojects.net/knowledge/ir/rc6.php)
+
+Sony protocol:
+[SIRC sbprojects.net](https://www.sbprojects.net/knowledge/ir/sirc.php)
+
+MCE protocol:
+[OrtekMCE](http://www.hifi-remote.com/johnsfine/DecodeIR.html#OrtekMCE)
+
+IR decoders (C sourcecode):
+[in the Linux kernel](https://github.com/torvalds/linux/tree/master/drivers/media/rc)
projects / micorpython_ir.git / blobdiff