README improvements.

[micorpython_ir.git] / README.md

diff --git a/README.md b/README.md
index d90a74f0145a9d61606ef4f60022ab529fc7badd..c1635194404241aecff2af41b06d2896a1f70b8b 100644 (file)
--- a/README.md
+++ b/README.md
@@ -8,13 +8,14 @@ require `uasyncio` but are compatible with it.
 
 IR communication uses a carrier frequency to pulse the IR source. Modulation
 takes the form of OOK (on-off keying). There are multiple protocols and at
 
 IR communication uses a carrier frequency to pulse the IR source. Modulation
 takes the form of OOK (on-off keying). There are multiple protocols and at

-least two options for carrier frequency, namely 36KHz and 38KHz.
+least three options for carrier frequency, namely 36KHz, 38KHz and 40KHz.

 
 

-The drivers support the NEC protocol and two Philips protocols, namely RC-5 and
-RC-6 mode 0. In the case of the transmitter the carrier frequency is a runtime
-parameter: any value may be specified. The receiver uses a hardware demodulator
-which must be specified for the correct frequency. The receiver device driver
-sees the demodulated signal and is hence carrier frequency agnostic.
+The drivers support NEC and Sony protocols and two Philips protocols, namely
+RC-5 and RC-6 mode 0. In the case of the transmitter the carrier frequency is a
+runtime parameter: any value may be specified. The receiver uses a hardware
+demodulator which should be specified for the correct frequency. The receiver
+device driver sees the demodulated signal and is hence carrier frequency
+agnostic.

 
 Examining waveforms from various remote controls it is evident that numerous
 protocols exist. Some are doubtless proprietary and undocumented. The supported
 
 Examining waveforms from various remote controls it is evident that numerous
 protocols exist. Some are doubtless proprietary and undocumented. The supported


@@ -41,6 +42,9 @@ demodulates the 38KHz IR pulses and passes the demodulated pulse train to the
 microcontroller. The tested chip returns a 0 level on carrier detect, but the
 driver design should ensure operation regardless of sense.
 
 microcontroller. The tested chip returns a 0 level on carrier detect, but the
 driver design should ensure operation regardless of sense.
 

+In my testing a 38KHz demodulator worked with 36KHz and 40KHz remotes, but this
+is obviously not guaranteed or optimal.
+

 The pin used to connect the decoder chip to the target is arbitrary but the
 test programs assume pin X3 on the Pyboard, pin 13 on the ESP8266 and pin 23 on
 ESP32.
 The pin used to connect the decoder chip to the target is arbitrary but the
 test programs assume pin X3 on the Pyboard, pin 13 on the ESP8266 and pin 23 on
 ESP32.


@@ -84,22 +88,34 @@ from the official library and `aswitch.py` from
 
 # 4. Receiver
 
 
 # 4. Receiver
 

-This implements a class for each supported protocol, namely `NEC_IR`, `RC5_IR`
-and `RC6_M0`. Applications should instantiate the appropriate class with a
-callback. The callback will run whenever an IR pulsetrain is received.
+This implements a class for each supported protocol, namely `NEC_IR`,
+`SONY_IR`, `RC5_IR` and `RC6_M0`. Applications should instantiate the
+appropriate class with a callback. The callback will run whenever an IR pulse
+train is received.

 
 Constructor:  
 `NEC_IR` args: `pin`, `callback`, `extended=True`, `*args`  
 
 Constructor:  
 `NEC_IR` args: `pin`, `callback`, `extended=True`, `*args`  

+`SONY_IR` args: `pin`, `callback`, `bits=20`, `*args`  

 `RC5_IR` and `RC6_M0`: args `pin`, `callback`, `*args`  
 `RC5_IR` and `RC6_M0`: args `pin`, `callback`, `*args`  

-Args:  
+
+Args (all protocols):  

  1. `pin` is a `machine.Pin` instance configured as an input, connected to the
  IR decoder chip.  
  2. `callback` is the user supplied callback (see below).
  1. `pin` is a `machine.Pin` instance configured as an input, connected to the
  IR decoder chip.  
  2. `callback` is the user supplied callback (see below).

- 3. `extended` is an NEC specific boolean. Remotes using the NEC protocol can
+ 4. `*args` Any further args will be passed to the callback.  
+
+Protocol specific args:
+ 1. `extended` is an NEC specific boolean. Remotes using the NEC protocol can

  send 8 or 16 bit addresses. If `True` 16 bit addresses are assumed - an 8 bit
  address will be correctly received. Set `False` to enable extra error checking
  for remotes that return an 8 bit address.
  send 8 or 16 bit addresses. If `True` 16 bit addresses are assumed - an 8 bit
  address will be correctly received. Set `False` to enable extra error checking
  for remotes that return an 8 bit address.

- 4. `*args` Any further args will be passed to the callback.  
+ 2. `bits=20` Sony specific. The SIRC protocol comes in 3 variants: 12, 15 and
+ 20 bits. The default will handle bitstreams from all three types of remote. A
+ value matching your remote improves the timing and reduces the  likelihood of
+ errors when handling repeats: in 20-bit mode SIRC timing when a button is held
+ down is tight. A worst-case 20-bit block takes 39ms nominal, yet the repeat
+ time is 45ms nominal.  
+ The Sony remote tested issues both 12 bit and 15 bit streams.

 
 The callback takes the following args:  
  1. `data` Integer value fom the remote. A negative value indicates an error
 
 The callback takes the following args:  
  1. `data` Integer value fom the remote. A negative value indicates an error


@@ -107,7 +123,9 @@ The callback takes the following args:
  2. `addr` Address from the remote
  3. `ctrl` 0 in the case of NEC. Philips protocols toggle this bit on repeat
  button presses. If the button is held down the bit is not toggled. The
  2. `addr` Address from the remote
  3. `ctrl` 0 in the case of NEC. Philips protocols toggle this bit on repeat
  button presses. If the button is held down the bit is not toggled. The

- transmitter demo implements this behaviour.
+ transmitter demo implements this behaviour.  
+ In the case of Sony the value will be 0 unless receiving a 20-bit stream, in
+ which case it will hold the extended value.

  4. Any args passed to the constructor.
 
 Class variable:  
  4. Any args passed to the constructor.
 
 Class variable:  


@@ -174,8 +192,8 @@ for a repeat code. Philips codes: RC-5 900μs, RC-6 mode 0 5.5ms.
 
 This is specific to Pyboard D and Pyboard 1.x (not Lite).
 
 
 This is specific to Pyboard D and Pyboard 1.x (not Lite).
 

-It implements a class for each supported protocol, namely `NEC`, `RC5` and
-`RC6_M0`. The application instantiates the appropriate class and calls the
+It implements a class for each supported protocol, namely `NEC`, `SONY`, `RC5`
+and `RC6_M0`. The application instantiates the appropriate class and calls the

 `transmit` method to send data.
 
 Constructor  
 `transmit` method to send data.
 
 Constructor  


@@ -184,18 +202,24 @@ All constructors take the following args:
  is employed by the test script. Must be connected to the IR diode as described
  below.
  2. `freq=default` The carrier frequency in Hz. The default for NEC is 38000,
  is employed by the test script. Must be connected to the IR diode as described
  below.
  2. `freq=default` The carrier frequency in Hz. The default for NEC is 38000,

- and for Philips is 36000.
+ Sony is 40000 and Philips is 36000.

  3. `verbose=False` If `True` emits debug output.
 
  3. `verbose=False` If `True` emits debug output.
 

+The `SONY` constructor is of form `pin, bits=12, freq=40000, verbose=False`.
+The `bits` value may be 12, 15 or 20 to set SIRC variant in use. Other args are
+as above.
+

 Method:
  1. `transmit(addr, data, toggle=0)` Integer args. `addr` and `data` are
 Method:
  1. `transmit(addr, data, toggle=0)` Integer args. `addr` and `data` are

- normally 8-bit values and `toggle` is 0 or 1.  
+ normally 8-bit values and `toggle` is normally 0 or 1.  

  In the case of NEC, if an address < 256 is passed, normal mode is assumed and
  the complementary value is appended. 16-bit values are transmitted as extended
  addresses.  
  In the case of NEC the `toggle` value is ignored. For Philips protocols it
  should be toggled each time a button is pressed, and retained if the button is
  In the case of NEC, if an address < 256 is passed, normal mode is assumed and
  the complementary value is appended. 16-bit values are transmitted as extended
  addresses.  
  In the case of NEC the `toggle` value is ignored. For Philips protocols it
  should be toggled each time a button is pressed, and retained if the button is

- held down. The test program illustrates a way to do this.
+ held down. The test program illustrates a way to do this.  
+ `SONY` ignores `toggle` unless in 20-bit mode, in which case it is transmitted
+ as the `extended` value and can be any integer in range 0 to 255.

 
 The `transmit` method is synchronous with rapid return. Actual transmission
 occurs as a background process, controlled by timers 2 and 5. Execution times
 
 The `transmit` method is synchronous with rapid return. Actual transmission
 occurs as a background process, controlled by timers 2 and 5. Execution times


@@ -214,7 +238,7 @@ increase power.
 
 The transistor type is not critical.
 
 
 The transistor type is not critical.
 

-These circuits assume circuits as shown. Here the carrier "off" state is 0V,
+The driver assumes circuits as shown. Here the carrier "off" state is 0V,

 which is the driver default. If using a circuit where "off" is required to be
 3.3V, the constant `_SPACE` in `ir_tx.py` should be changed to 100.
 
 which is the driver default. If using a circuit where "off" is required to be
 3.3V, the constant `_SPACE` in `ir_tx.py` should be changed to 100.
 


@@ -222,7 +246,7 @@ which is the driver default. If using a circuit where "off" is required to be
 
 The classes inherit from the abstract base class `IR`. This has an array `.arr`
 to contain the duration (in μs) of each carrier on or off period. The
 
 The classes inherit from the abstract base class `IR`. This has an array `.arr`
 to contain the duration (in μs) of each carrier on or off period. The

-`transmit` method calls a `tx` method in the subclass which populates this
+`transmit` method calls a `tx` method of the subclass which populates this

 array. On completion `transmit` appends a special `STOP` value and initiates
 physical transmission which occurs in an interrupt context.
 
 array. On completion `transmit` appends a special `STOP` value and initiates
 physical transmission which occurs in an interrupt context.
 


@@ -231,7 +255,7 @@ channel 1 is used to configure the output pin as a PWM channel. Its frequency
 is set in the constructor. The OOK is performed by dynamically changing the
 duty ratio using the timer channel's `pulse_width_percent` method: this varies
 the pulse width from 0 to a duty ratio passed to the constructor. The NEC
 is set in the constructor. The OOK is performed by dynamically changing the
 duty ratio using the timer channel's `pulse_width_percent` method: this varies
 the pulse width from 0 to a duty ratio passed to the constructor. The NEC

-protocol defaults to 50%, the Philips ones to 30%.
+protocol defaults to 50%, the Sony and Philips ones to 30%.

 
 The duty ratio is changed by the Timer 5 callback `._cb`. This retrieves the
 next duration from the array. If it is not `STOP` it toggles the duty cycle
 
 The duty ratio is changed by the Timer 5 callback `._cb`. This retrieves the
 next duration from the array. If it is not `STOP` it toggles the duty cycle


@@ -244,15 +268,17 @@ Philips protocols.
 
 # 6. References
 
 
 # 6. References
 

-The NEC protocol is described in these references:  
+[General information about IR](https://www.sbprojects.net/knowledge/ir/)
+
+The NEC protocol:  

 [altium](http://techdocs.altium.com/display/FPGA/NEC+Infrared+Transmission+Protocol)  
 [circuitvalley](http://www.circuitvalley.com/2013/09/nec-protocol-ir-infrared-remote-control.html)
 
 [altium](http://techdocs.altium.com/display/FPGA/NEC+Infrared+Transmission+Protocol)  
 [circuitvalley](http://www.circuitvalley.com/2013/09/nec-protocol-ir-infrared-remote-control.html)
 

-The Philips protocols may be found in these refs:  
+Philips protocols:  

 [RC5](https://en.wikipedia.org/wiki/RC-5)  
 [RC6](https://www.sbprojects.net/knowledge/ir/rc6.php)
 
 [RC5](https://en.wikipedia.org/wiki/RC-5)  
 [RC6](https://www.sbprojects.net/knowledge/ir/rc6.php)
 

-Sony protocol (future use):  
+Sony protocol:  

 [SIRC](https://www.sbprojects.net/knowledge/ir/sirc.php)
 
 # Appendix 1 NEC Protocol description
 [SIRC](https://www.sbprojects.net/knowledge/ir/sirc.php)
 
 # Appendix 1 NEC Protocol description