Receiver now a package.

[micorpython_ir.git] / README.md

diff --git a/README.md b/README.md
index 03e013e758efcd39a759681282f518601865b72c..1e1fa25b39e2374ea9718214a92945c219b009fc 100644 (file)
--- a/README.md
+++ b/README.md
@@ -2,114 +2,355 @@
 
 This repo provides a driver to receive from IR (infra red) remote controls and
 a driver for IR "blaster" apps. The device drivers are nonblocking. They do not
 
 This repo provides a driver to receive from IR (infra red) remote controls and
 a driver for IR "blaster" apps. The device drivers are nonblocking. They do not

-require `uasyncio` but are entirely compatible with it.
+require `uasyncio` but are compatible with it.
+
+The transmitter driver is specific to the Pyboard. The receiver is cross
+platform and has been tested on Pyboard, ESP8266 and ESP32. See
+[Receiver platforms](./README.md#42-receiver-platforms) for test results and
+limitations.
+
+# 1. IR communication

 
 IR communication uses a carrier frequency to pulse the IR source. Modulation
 
 IR communication uses a carrier frequency to pulse the IR source. Modulation

-takes the form of OOK (on-off keying). There are a several mutually
-incompatible protocols and at least two options for carrier frequency, namely
-36KHz and 38KHz.
+takes the form of OOK (on-off keying). There are multiple protocols and at
+least three options for carrier frequency, namely 36KHz, 38KHz and 40KHz.
+
+The drivers support NEC and Sony protocols and two Philips protocols, namely
+RC-5 and RC-6 mode 0. In the case of the transmitter the carrier frequency is a
+runtime parameter: any value may be specified. The receiver uses a hardware
+demodulator which should be purchased for the correct frequency. The receiver
+device driver sees the demodulated signal and is hence carrier frequency
+agnostic.
+
+Examining waveforms from various remote controls it is evident that numerous
+protocols exist. Some are doubtless proprietary and undocumented. The supported
+protocols are those for which I managed to locate documentation. My preference
+is for the NEC version. It has conservative timing and ample scope for error
+detection. RC-5 has limited error detection, and RC-6 mode 0 has rather fast
+timing.

 
 

-The drivers support the NEC protocol and two Philips protocols, namely RC-5 and
-RC-6 mode 0. In the case of the transmitter the carrier frequency is a runtime
-parameter so any value may be used. The receiver uses a hardware demodulator
-which must be specified for the correct frequency. The device driver is carrier
-frequency agnostic.
+A remote using the NEC protocol is [this one](https://www.adafruit.com/products/389).

 
 

-# Hardware Requirements
+Remotes transmit an address and a data byte, plus in some cases an extra value.
+The address denotes the physical device being controlled. The data defines the
+button on the remote. Provision usually exists for differentiating between a
+button repeatedly pressed and one which is held down; the mechanism is protocol
+dependent.
+
+# 2. Hardware Requirements

 
 The receiver is cross-platform. It requires an IR receiver chip to demodulate
 
 The receiver is cross-platform. It requires an IR receiver chip to demodulate

-the carrier. There are two options for carrier frequency: 36KHz and 38KHz. The
-chip must be selected for the frequency in use by the remote. 
+the carrier. The chip must be selected for the frequency in use by the remote.
+For 38KHz devices a receiver chip such as the Vishay TSOP4838 or the
+[adafruit one](https://www.adafruit.com/products/157) is required. This
+demodulates the 38KHz IR pulses and passes the demodulated pulse train to the
+microcontroller. The tested chip returns a 0 level on carrier detect, but the
+driver design ensures operation regardless of sense.
+
+In my testing a 38KHz demodulator worked with 36KHz and 40KHz remotes, but this
+is obviously neither guaranteed nor optimal.
+
+The pin used to connect the decoder chip to the target is arbitrary. The test
+program assumes pin X3 on the Pyboard, pin 23 on ESP32 and pin 13 on ESP8266.
+On the WeMos D1 Mini the equivalent pin is D7.

 
 The transmitter requires a Pyboard 1.x (not Lite) or a Pyboard D. Output is via
 an IR LED which will normally need a transistor to provide sufficient current.
 
 The transmitter requires a Pyboard 1.x (not Lite) or a Pyboard D. Output is via
 an IR LED which will normally need a transistor to provide sufficient current.

+Typically these need 50-100mA of drive to achieve reasonable range and data
+integrity. A suitable LED is [this one](https://www.adafruit.com/product/387).

 
 

-# Decoder for IR Remote Controls using the NEC protocol
+The transmitter test script assumes pin X1 for IR output. It can be changed,
+but it must support Timer 2 channel 1. Pins for pushbutton inputs are
+arbitrary: X3 and X4 are used.

 
 

-This protocol is widely used. An example remote is [this one](https://www.adafruit.com/products/389).
-To interface the device a receiver chip such as the Vishay TSOP4838 or the
-[adafruit one](https://www.adafruit.com/products/157) is required. This
-demodulates the 38KHz IR pulses and passes the demodulated pulse train to the
-microcontroller.
+# 3. Installation

 
 

-The driver and test programs run on the Pyboard and ESP8266.
+On import, demos print an explanation of how to run them.

 
 

-# Files
+## 3.1 Receiver

 
 

- 1. `aremote.py` The device driver.
- 2. `art.py` A test program to characterise a remote.
- 3. `art1.py` Control an onboard LED using a remote. The data and addresss
- values need changing to match your characterised remote.
+This is a Python package. This minimises RAM usage: applications only import
+the device driver for the protocol in use.

 
 

-# Dependencies
+Copy the following to the target filesystem:
+ 1. `ir_rx` Directory and contents. Contains the device drivers.
+ 2. `ir_rx_test.py` Demo of a receiver.

 
 

-The driver requires the `uasyncio` library and the file `asyn.py` from this
-repository.
+There are no dependencies.

 
 

-# Usage
+The demo can be used to characterise IR remotes. It displays the codes returned
+by each button. This can aid in the design of receiver applications. The demo
+prints "running" every 5 seconds and reports any data received from the remote.

 
 

-The pin used to connect the decoder chip to the target is arbitrary but the
-test programs assume pin X3 on the Pyboard and pin 13 on the ESP8266.
+## 3.2 Transmitter

 
 

-The driver is event driven. Pressing a button on the remote causes a user
-defined callback to be run. The NEC protocol returns a data value and an
-address. These are passed to the callback as the first two arguments (further
-user defined arguments may be supplied). The address is normally constant for a
-given remote, with the data corresponding to the button. Applications should
-check the address to ensure that they only respond to the correct remote.
+Copy the following files to the Pyboard filesystem:
+ 1. `ir_tx.py` The transmitter device driver.
+ 2. `ir_tx_test.py` Demo of a 2-button remote controller.

 
 

-Data values are 8 bit. Addresses may be 8 or 16 bit depending on whether the
-remote uses extended addressing.
+The device driver has no dependencies. The test program requires `uasyncio`
+from the official library and `aswitch.py` from
+[this repo](https://github.com/peterhinch/micropython-async).

 
 

-If a button is held down a repeat code is sent. In this event the driver
-returns a data value of `REPEAT` and the address associated with the last
-valid data block.
+# 4. Receiver

 
 

-To characterise a remote run `art.py` and note the data value for each button
-which is to be used. If the address is less than 256, extended addressing is
-not in use.
+This implements a class for each supported protocol. Applications should
+instantiate the appropriate class with a callback. The callback will run
+whenever an IR pulse train is received. Example running on a Pyboard:

 
 

-# Reliability
+```python
+import time
+from machine import Pin
+from pyb import LED
+from ir_rx.nec import NEC_8  # NEC remote, 8 bit addresses

 
 

-IR reception is inevitably subject to errors, notably if the remote is operated
-near the limit of its range, if it is not pointed at the receiver or if its
-batteries are low. So applications must check for, and usually ignore, errors.
-These are flagged by data values < `REPEAT`.
+red = LED(1)

 
 

-On the ESP8266 there is a further source of errors. This results from the large
-and variable interrupt latency of the device which can exceed the pulse
-duration. This causes pulses to be missed. This tendency is slightly reduced by
-running the chip at 160MHz.
+def callback(data, addr, ctrl):
+    if data < 0:  # NEC protocol sends repeat codes.
+        print('Repeat code.')
+    else:
+        print('Data {:02x} Addr {:04x}'.format(data, addr))

 
 

-In general applications should provide user feedback of correct reception.
-Users tend to press the key again if no acknowledgement is received.
+ir = NEC_8(Pin('X3', Pin.IN), callback)
+while True:
+    time.sleep_ms(500)
+    red.toggle()
+```
+
+#### Common to all classes
+
+Constructor:  
+Args:  
+ 1. `pin` is a `machine.Pin` instance configured as an input, connected to the
+ IR decoder chip.  
+ 2. `callback` is the user supplied callback.
+ 3. `*args` Any further args will be passed to the callback.  
+
+The user callback takes the following args:  
+ 1. `data` (`int`) Value from the remote. Normally in range 0-255. A value < 0
+ signifies an NEC repeat code.
+ 2. `addr` (`int`) Address from the remote.
+ 3. `ctrl` (`int`) The meaning of this is protocol dependent:  
+ NEC: 0  
+ Philips: this is toggled 1/0 on repeat button presses. If the button is held
+ down it is not toggled. The  transmitter demo implements this behaviour.  
+ Sony: 0 unless receiving a 20-bit stream, in which case it holds the extended
+ value.
+ 4. Any args passed to the constructor.
+
+Bound variable:  
+ 1. `verbose=False` If `True` emits debug output.
+
+Method:
+ 1. `error_function` Arg: a function taking a single arg. If this is specified
+ it will be called if an error occurs. The value corresponds to the error code
+ (see below).
+
+#### NEC classes
+
+`NEC_8`, `NEC_16`
+
+```python
+from ir_rx.nec import NEC_8
+```
+
+Remotes using the NEC protocol can send 8 or 16 bit addresses. If the `NEC_16`
+class receives an 8 bit address it will get a 16 bit value comprising the
+address in bits 0-7 and its one's complement in bits 8-15.  
+The `NEC_8` class enables error checking for remotes that return an 8 bit
+address: the complement is checked and the address returned as an 8-bit value.
+A 16-bit address will result in an error.
+
+#### Sony classes
+
+`SONY_12`, `SONY_15`, `SONY_20`
+
+```python
+from ir_rx.sony import SONY_15
+```
+
+The SIRC protocol comes in 3 variants: 12, 15 and 20 bits. `SONY_20` handles
+bitstreams from all three types of remote. Choosing a class matching the remote
+improves the timing reducing the likelihood of errors when handling repeats: in
+20-bit mode SIRC timing when a button is held down is tight. A worst-case 20
+bit block takes 39ms nominal, yet the repeat time is 45ms nominal.  
+A single physical remote can issue more than one type of bitstream. The Sony
+remote tested issued both 12 bit and 15 bit streams.
+
+#### Philips classes
+
+`RC5_IR`, `RC6_M0`

 
 

-# The NEC_IR class
+```python
+from ir_rx.philips import RC5_IR
+```

 
 

-The constructor takes the following positional arguments.
+These support the RC-5 and RC-6 mode 0 protocols respectively.

 
 

- 1. `pin` A `Pin` instance for the decoder chip.
- 2. `cb` The user callback function.
- 3. `extended` Set `False` to enable extra error checking if the remote
- returns an 8 bit address.
- 4. Further arguments, if provided, are passed to the callback.
+# 4.1 Errors

 
 

-The callback receives the following positional arguments:
+IR reception is inevitably subject to errors, notably if the remote is operated
+near the limit of its range, if it is not pointed at the receiver or if its
+batteries are low. The user callback is not called when an error occurs.

 
 

- 1. The data value returned from the remote.
- 2. The address value returned from the remote.
- 3. Any further arguments provided to the `NEC_IR` constructor.
+On ESP8266 and ESP32 there is a further source of errors. This results from the
+large and variable interrupt latency of the device which can exceed the pulse
+duration. This causes pulses to be missed or their timing measured incorrectly.
+On ESP8266 some improvment may be achieved by running the chip at 160MHz.

 
 

-Negative data values are used to signal repeat codes and transmission errors.
+In general applications should provide user feedback of correct reception.
+Users tend to press the key again if the expected action is absent.

 
 

-The test program `art1.py` provides an example of a minimal application.
+In debugging a callback can be specified for reporting errors. The value passed
+to the error function are represented by constants indicating the cause of the
+error. These are as follows:

 
 

-# How it works
+`BADSTART` A short (<= 4ms) start pulse was received. May occur due to IR
+interference, e.g. from fluorescent lights. The TSOP4838 is prone to producing
+200µs pulses on occasion, especially when using the ESP8266.  
+`BADBLOCK` A normal data block: too few edges received. Occurs on the ESP8266
+owing to high interrupt latency.  
+`BADREP` A repeat block: an incorrect number of edges were received.  
+`OVERRUN` A normal data block: too many edges received.  
+`BADDATA` Data did not match check byte.  
+`BADADDR` (`NEC_IR`) If `extended` is `False` the 8-bit address is checked
+against the check byte. This code is returned on failure.  

 
 

-The NEC protocol is described in these references.  
+# 4.2 Receiver platforms
+
+Currently the ESP8266 suffers from [this issue](https://github.com/micropython/micropython/issues/5714).
+Testing was therefore done without WiFi connectivity.
+
+Philips protocols (especially RC-6) have tight timing constraints with short
+pulses whose length must be determined with reasonable accuracy. The Sony 20
+bit protocol also has a timing issue in that the worst case bit pattern takes
+39ms nominal, yet the repeat time is 45ms nominal. These issues can lead to
+errors particularly on slower targets. As discussed above, errors are to be
+expected. It is up to the user to decide if the error rate is acceptable.
+
+Reception was tested using Pyboard D SF2W, ESP8266 and ESP32 with signals from
+remote controls (where available) and from the tranmitter in this repo. Issues
+are listed below.
+
+NEC: No issues.  
+Sony 12 and 15 bit: No issues.  
+Sony 20 bit: On ESP32 some errors occurred when repeats occurred.  
+Philips RC-5: On ESP32 with one remote control many errors occurred, but paired
+with the transmitter in this repo it worked.  
+Philips RC-6: No issues. Only tested against the transmitter in this repo.
+
+# 4.3 Principle of operation
+
+Protocol classes inherit from the abstract base class `IR_RX`. This uses a pin
+interrupt to store in an array the start and end times of pulses (in μs).
+Arrival of the first pulse triggers a software timer which runs for the
+expected duration of an IR block (`tblock`). When it times out its callback
+(`.decode`) decodes the data and calls the user callback. The use of a software
+timer ensures that `.decode` and the user callback can allocate.
+
+The size of the array and the duration of the timer are protocol dependent and
+are set by the subclasses. The `.decode` method is provided in the subclass.
+
+CPU times used by `.decode` (not including the user callback) were measured on
+a Pyboard D SF2W at stock frequency. They were: NEC 1ms for normal data, 100μs
+for a repeat code. Philips codes: RC-5 900μs, RC-6 mode 0 5.5ms.
+
+# 5 Transmitter
+
+This is specific to Pyboard D and Pyboard 1.x (not Lite).
+
+It implements a class for each supported protocol, namely `NEC`, `SONY`, `RC5`
+and `RC6_M0`. The application instantiates the appropriate class and calls the
+`transmit` method to send data.
+
+Constructor  
+All constructors take the following args:  
+ 1. `pin` An initialised `pyb.Pin` instance supporting Timer 2 channel 1: `X1`
+ is employed by the test script. Must be connected to the IR diode as described
+ below.
+ 2. `freq=default` The carrier frequency in Hz. The default for NEC is 38000,
+ Sony is 40000 and Philips is 36000.
+ 3. `verbose=False` If `True` emits debug output.
+
+The `SONY` constructor is of form `pin, bits=12, freq=40000, verbose=False`.
+The `bits` value may be 12, 15 or 20 to set SIRC variant in use. Other args are
+as above.
+
+Method:
+ 1. `transmit(addr, data, toggle=0)` Integer args. `addr` and `data` are
+ normally 8-bit values and `toggle` is normally 0 or 1.  
+ In the case of NEC, if an address < 256 is passed, normal mode is assumed and
+ the complementary value is appended. 16-bit values are transmitted as extended
+ addresses.  
+ In the case of NEC the `toggle` value is ignored. For Philips protocols it
+ should be toggled each time a button is pressed, and retained if the button is
+ held down. The test program illustrates a way to do this.  
+ `SONY` ignores `toggle` unless in 20-bit mode, in which case it is transmitted
+ as the `extended` value and can be any integer in range 0 to 255.
+
+The `transmit` method is synchronous with rapid return. Actual transmission
+occurs as a background process, controlled by timers 2 and 5. Execution times
+on a Pyboard 1.1 were 3.3ms for NEC, 1.5ms for RC5 and 2ms for RC6.
+
+# 5.1 Wiring
+
+I use the following circuit which delivers just under 40mA to the diode. R2 may
+be reduced for higher current.  
+![Image](images/circuit.png)
+
+This alternative delivers a constant current of about 53mA if a higher voltage
+than 5V is available. R4 determines the current value and may be reduced to
+increase power.  
+![Image](images/circuit2.png)
+
+The transistor type is not critical.
+
+The driver assumes circuits as shown. Here the carrier "off" state is 0V,
+which is the driver default. If using a circuit where "off" is required to be
+3.3V, the constant `_SPACE` in `ir_tx.py` should be changed to 100.
+
+# 5.2 Principle of operation
+
+The classes inherit from the abstract base class `IR`. This has an array `.arr`
+to contain the duration (in μs) of each carrier on or off period. The
+`transmit` method calls a `tx` method of the subclass which populates this
+array. On completion `transmit` appends a special `STOP` value and initiates
+physical transmission which occurs in an interrupt context.
+
+This is performed by two hardware timers initiated in the constructor. Timer 2,
+channel 1 is used to configure the output pin as a PWM channel. Its frequency
+is set in the constructor. The OOK is performed by dynamically changing the
+duty ratio using the timer channel's `pulse_width_percent` method: this varies
+the pulse width from 0 to a duty ratio passed to the constructor. The NEC
+protocol defaults to 50%, the Sony and Philips ones to 30%.
+
+The duty ratio is changed by the Timer 5 callback `._cb`. This retrieves the
+next duration from the array. If it is not `STOP` it toggles the duty cycle
+and re-initialises T5 for the new duration.
+
+The `IR.append` enables times to be added to the array, keeping track of the
+notional carrier on/off state for biphase generation. The `IR.add` method
+facilitates lengthening a pulse as required in the biphase sequences used in
+Philips protocols.
+
+# 6. References
+
+[General information about IR](https://www.sbprojects.net/knowledge/ir/)
+
+The NEC protocol:  

 [altium](http://techdocs.altium.com/display/FPGA/NEC+Infrared+Transmission+Protocol)  
 [circuitvalley](http://www.circuitvalley.com/2013/09/nec-protocol-ir-infrared-remote-control.html)
 
 [altium](http://techdocs.altium.com/display/FPGA/NEC+Infrared+Transmission+Protocol)  
 [circuitvalley](http://www.circuitvalley.com/2013/09/nec-protocol-ir-infrared-remote-control.html)
 

+Philips protocols:  
+[RC5](https://en.wikipedia.org/wiki/RC-5)  
+[RC6](https://www.sbprojects.net/knowledge/ir/rc6.php)
+
+Sony protocol:  
+[SIRC](https://www.sbprojects.net/knowledge/ir/sirc.php)
+
+# Appendix 1 NEC Protocol description
+

 A normal burst comprises exactly 68 edges, the exception being a repeat code
 which has 4. An incorrect number of edges is treated as an error. All bursts
 begin with a 9ms pulse. In a normal code this is followed by a 4.5ms space; a
 A normal burst comprises exactly 68 edges, the exception being a repeat code
 which has 4. An incorrect number of edges is treated as an error. All bursts
 begin with a 9ms pulse. In a normal code this is followed by a 4.5ms space; a


@@ -135,25 +376,3 @@ any asyncio latency when setting its delay period.
 The algorithm promotes interrupt handler speed over RAM use: the 276 bytes used
 for the data array could be reduced to 69 bytes by computing and saving deltas
 in the interrupt service routine.
 The algorithm promotes interrupt handler speed over RAM use: the 276 bytes used
 for the data array could be reduced to 69 bytes by computing and saving deltas
 in the interrupt service routine.

-
-# Error returns
-
-Data values passed to the callback are normally positive. Negative values
-indicate a repeat code or an error.
-
-`REPEAT` A repeat code was received.
-
-Any data value < `REPEAT` denotes an error. In general applications do not
-need to decode these, but they may be of use in debugging. For completeness
-they are listed below.
-
-`BADSTART` A short (<= 4ms) start pulse was received. May occur due to IR
-interference, e.g. from fluorescent lights. The TSOP4838 is prone to producing
-200µs pulses on occasion, especially when using the ESP8266.  
-`BADBLOCK` A normal data block: too few edges received. Occurs on the ESP8266
-owing to high interrupt latency.  
-`BADREP` A repeat block: an incorrect number of edges were received.  
-`OVERRUN` A normal data block: too many edges received.  
-`BADDATA` Data did not match check byte.  
-`BADADDR` Where `extended` is `False` the 8-bit address is checked
-against the check byte. This code is returned on failure.